# Fleece-reinforced membranes: why details stay dry

Source: https://roofingbyskyline.com/blog/fleece-reinforced-liquid-waterproofing

> How fleece-reinforced membranes such as Kemper System’s KEMPEROL work on crowded roofs and tiled balconies, and what Approved Applicator means for the warranty.

Published 2026-10-11 · Waterproofing

Walk any flat roof in San Francisco and count the things that interrupt the membrane: a skylight curb, two vent stacks, conduit for the solar array, a drain, a parapet with a coping cap, a door to a roof deck. Every one of those is a detail — and with sheet membranes, every detail is a seam, a boot or a piece of pre-formed flashing that has to be sealed to the field.

Fleece-reinforced liquid membranes take a different approach: **the details are made from the same material as the field, in one continuous operation.**

## How the system is built

1. **Prepare and prime.** The substrate is cleaned, repaired and checked for moisture; the primer is selected for that substrate.
2. **Apply resin.** A coat of liquid resin goes down on a section of roof — or around a penetration.
3. **Embed the fleece wet-on-wet.** A polyester fleece is rolled into the wet resin. Laps overlap the fleece, never butt it.
4. **Saturate from above.** More resin is applied over the fleece until it’s fully encapsulated.
5. **Surface as specified.** A reflective finish, a wearing course for traffic, or protection for pavers, tile or soil above.

**Diagram — Fleece-reinforced liquid membrane** (layers from the substrate up):

1. Structural roof deck — Concrete, plywood or cover board
2. Insulation & cover board — Tapered where drainage needs correcting
3. Primer — Chosen after adhesion testing
4. Resin — saturation coat — Applied wet to receive the fleece
5. Polyester fleece reinforcement — Embedded wet-on-wet, overlapped at laps
6. Resin — top saturation — Fully encapsulates the fleece
7. Surfacing (as specified) — Reflective finish or wearing surface

Because the fleece runs through the whole membrane, the finished thickness is controlled by the fleece and the resin consumption — not by how heavily someone rolled a coat. And because the resin is liquid, it wraps a pipe, a curb or an odd-shaped corner as easily as a flat field.

## Why it suits Bay Area buildings

- **Crowded roofs.** Small city roofs often have more detail than field. A self-flashing membrane turns dozens of potential leak points into one continuous surface.
- **Roof-to-deck transitions.** The same membrane can run from a roof onto a balcony or roof deck without a seam between systems.
- **Under tile and pavers.** Fully bonded, reinforced membranes are used beneath tile, pavers, pedestals and planters.
- **Green roofs and planters.** Root-resistant formulations are available for vegetated assemblies.
- **No torches.** Cold-applied resins avoid open flame on wood-framed buildings.

## Polyurethane or PMMA?

Kemper System makes both. **KEMPEROL 2K-PUR** is a two-component, solvent-free polyurethane resin used on roofs, plazas, balconies, planters, foundations and wet areas. **KEMPEROL AC Speed FR** is a fast-curing PMMA resin — useful when a schedule is tight or a surface has to be back in service quickly. PMMA has a noticeable odor while it cures, so on occupied buildings we plan around air intakes and windows, or choose the polyurethane resin instead.

## The Kemper System story, briefly

Kemper System was founded in Germany in 1957 and has been building fleece-reinforced liquid roofs since the late 1960s. In the US, Kemper System America is based in West Seneca, New York.

## Why “Approved Applicator” matters

Kemper System doesn’t sell warranties to anyone with a roller. Contractors are trained on the job by Kemper, must retrain every two years, and only Approved Applicators can register Kemper warranties — which range from material-only coverage to watertightness warranties of up to 25 years on qualifying, fully reinforced systems.

We’re a Kemper System Approved Applicator. If your roof, balcony or podium has more detail than field, [let’s look at it together](https://roofingbyskyline.com/contact).

## Contact

- Phone: (415) 209-5199 (+1-415-209-5199)
- Email: info@roofingbyskyline.com
- Hours: Monday–Friday, 8am–5pm
- Service area: San Francisco and the greater Bay Area — San Francisco, The Peninsula, The East Bay, The South Bay, Marin
- License: California C-39 Roofing, CSLB #1138836 (verify: https://www.cslb.ca.gov/OnlineServices/CheckLicenseII/CheckLicense.aspx)
- Request a free assessment: https://roofingbyskyline.com/contact
