# Liquid-applied flat roof waterproofing

Source: https://roofingbyskyline.com/waterproofing/flat-roof-waterproofing

> Seamless, fleece-reinforced liquid waterproofing for flat and low-slope roofs, installed by a Kemper System Approved Applicator in the Bay Area.

San Francisco roofs are crowded: parapets, skylights, mechanical curbs, conduit, solar stanchions and drains, often on a roof the size of a living room. Every one of those details is a seam in a sheet membrane. A liquid membrane doesn’t have seams.

We install Kemper System’s cold liquid-applied, polyester-fleece-reinforced membranes as an Approved Applicator. The resin is applied, the fleece is embedded wet-on-wet, and the result is a single monolithic membrane that wraps every detail continuously.

## Ideal for

- Small, detail-heavy city roofs
- Roofs with many penetrations or solar mounts
- Parapet walls and curbs
- Roof-to-deck transitions
- Green roofs and planters (root-resistant systems)

## Why it works

- **Seamless by design.** There are no lap seams or welds to fail. The membrane is continuous from field to flashing.
- **Self-flashing details.** Penetrations, drains, parapets and odd geometry are flashed with the same reinforced resin as the field — no pre-formed boots to come loose.
- **Fully reinforced.** The polyester fleece gives the membrane tensile strength and a consistent, measurable thickness everywhere.
- **Cold-applied.** No torches or kettles on the roof. That matters on wood-framed buildings and occupied properties.
- **Reflective options.** Light-colored, cool-roof-rated finishes are available where California’s Title 24 energy code applies.
- **Long warranty paths.** Kemper System offers watertightness warranties on qualifying, fully reinforced systems — issued only through Approved Applicators like us.

## The system: Fleece-reinforced liquid membrane

Cold liquid-applied resin with a polyester fleece embedded wet-on-wet — one seamless, fully reinforced membrane that wraps parapets, drains and penetrations without a single lap seam to fail.

Layers, from the substrate up:

1. **Structural roof deck** — Concrete, plywood or cover board
2. **Insulation & cover board** — Tapered where drainage needs correcting
3. **Primer** — Chosen after adhesion testing
4. **Resin — saturation coat** — Applied wet to receive the fleece
5. **Polyester fleece reinforcement** — Embedded wet-on-wet, overlapped at laps
6. **Resin — top saturation** — Fully encapsulates the fleece
7. **Surfacing (as specified)** — Reflective finish or wearing surface

Systems we install for this work: [Kemper System](https://roofingbyskyline.com/waterproofing/products/kemper-system.md) (Kemper System Approved Applicator), [GacoFlex](https://roofingbyskyline.com/waterproofing/products/gacoflex.md) (Gaco Qualified Applicator).

## Our process

1. **Survey and test.** Core cuts or moisture survey of the existing roof, drainage review, and adhesion tests on the substrate we’ll be bonding to.
2. **Prepare and detail.** Remove failed material, correct ponding with tapered insulation where needed, prime, and flash every penetration first.
3. **Install wet-on-wet.** Resin, fleece and top saturation go down in one continuous operation, with laps overlapped and every coverage rate checked.
4. **Inspect and document.** Visual inspection, thickness verification and a photo record of every detail before surfacing and closeout.

## Quality checks on every job

- Resin consumption tracked against the manufacturer’s coverage rate
- Fleece laps overlapped to the system requirement — no butt joints
- Every penetration flashed in the same reinforced system as the field
- Substrate moisture and adhesion confirmed before priming
- Ponding corrected with slope, not with extra coating

## Warning signs

- Leaks around skylights, curbs or conduit
- Blistered or split seams in the existing membrane
- Ponding that never fully dries
- Repeated “patch” repairs at the same detail

## FAQ

### How is a liquid membrane different from a roof coating?

A coating is a protective layer, usually over an existing roof. A fleece-reinforced liquid membrane is the waterproofing itself: reinforced, built to a controlled thickness and detailed like a new roof.

### Can it go over my existing roof?

Often, if the existing roof is dry, sound and well attached, and the manufacturer approves the substrate. Wet insulation or delaminated layers have to come out first. We confirm with cores and adhesion tests.

### Is it safe to install on an occupied building?

The Kemper System polyurethane resins we use are solvent-free and cold-applied — no open flame. Fast-curing PMMA versions have a noticeable odor during application, so we plan air intakes, windows and timing with you.

### Can it handle foot traffic or pavers?

Yes. Wearing surfaces can be added over the membrane for walkways and roof decks, and the system can be used beneath pavers, tile or planters.


## Contact

- Phone: (415) 209-5199 (+1-415-209-5199)
- Email: info@roofingbyskyline.com
- Hours: Monday–Friday, 8am–5pm
- Service area: San Francisco and the greater Bay Area — San Francisco, The Peninsula, The East Bay, The South Bay, Marin
- License: California C-39 Roofing, CSLB #1138836 (verify: https://www.cslb.ca.gov/OnlineServices/CheckLicenseII/CheckLicense.aspx)
- Request a free assessment: https://roofingbyskyline.com/contact
