Skip to content

Waterproofing · 2 min read

Flood tests before waterproofing is covered

Once tile, pavers or soil go down, a membrane defect is expensive to find. How ASTM D5957 flood testing and ASTM D7877 electronic leak detection work.

By The Skyline team ·

A waterproofing membrane can look perfect and still have a pinhole at a drain, an unbonded lap or a nick from a dropped tool. On an exposed roof, you’d find that at the first storm and fix it in an afternoon. Under a paver deck, a planter or a tiled balcony, you’d find it as a stain on the ceiling below — and fixing it means tearing out everything on top.

That’s why we test horizontal waterproofing over occupied space before it’s covered.

Flood testing (ASTM D5957)

ASTM D5957 is the industry’s Standard Guide for Flood Testing Horizontal Waterproofing Installations. The idea is simple: dam the area, flood it with water, wait, and look underneath.

How it works on our projects:

  1. Plan the test with the structure in mind. Water is heavy — about 5.2 pounds per square foot for every inch of depth — so dam heights are kept modest and large areas are tested in sections.
  2. Dam and plug. Temporary dams go around the test area; drains are plugged or sleeved so the water level holds.
  3. Flood and mark. Water is added to the specified depth and the level is marked so any drop is obvious.
  4. Wait and watch. The water stays in place for the duration the specification calls for — commonly 24 hours or longer — while someone checks the space below.
  5. Drain, document, cover. If it passes, we photograph the result and install protection or the next layer promptly, before other trades walk on it.

Where it fits: D5957 is intended for horizontal waterproofing with very little slope — plaza decks, podiums, planters, balconies and similar areas. It is not intended as a test for roofing systems, and steeply sloped areas are hard to flood without many small dams.

Electronic leak detection (ASTM D7877)

ASTM D7877 covers electronic methods for detecting and locating leaks in roofing and waterproofing membranes. Most membranes are electrical insulators; the structural deck beneath is conductive. Technicians apply a low-voltage charge across the membrane and trace where current finds a path through it — which pinpoints the breach.

Strengths:

  • Locates the exact spot of a defect instead of just proving that one exists
  • Works on sloped surfaces and on roofs, where flooding isn’t practical
  • No heavy water loads on the structure
  • Some methods can be used after certain overburdens are in place

Limits: The method needs a conductive layer beneath the membrane. Concrete usually provides it; wood decks may need a conductive layer planned into the assembly from the start. That’s a design decision, so we raise it early.

Our rule

If a horizontal membrane is going to be buried under tile, pavers, a topping slab or soil, it gets tested before it disappears — by flood test or electronic leak detection, whichever suits the assembly.

Testing is part of a system, not a substitute for one

Testing catches defects; it doesn’t prevent them. The membrane still needs a sound, dry substrate, slope to drain, details flashed first and verified thickness. Testing is simply the final proof that all of that was done right — and the record you keep in your building file.

Protected membrane under plaza overburden

Protected membrane under plaza overburden: 1. Structural concrete slab, 2. Primer, 3. Reinforced waterproofing membrane, 4. Protection course, 5. Drainage composite, 6. Insulation (where specified), 7. Pavers, planters or green roof

What to ask your contractor

  • Will the membrane be tested before it’s covered? By what method?
  • Who watches the space below during a flood test, and for how long?
  • Will I get photos and a written record of the result?
  • If the deck is wood-framed and electronic testing is planned, how will the conductive layer be provided?

Planning a podium, roof deck or tiled balcony? Talk to us early — testing is easiest when it’s designed in.

Talk to someone who’s been on the roof.

Free assessments across the Bay Area. Written, fixed-price proposals.

Request an assessmentor call (415) 209-5199
Free assessment

Let’s keep the water out — for good.

Tell us what’s going on. We’ll inspect, explain what we find with photos, and give you a written, fixed-price proposal — usually within 48 hours of the visit.